You have a table of numbers and need a map that shows them honestly. Among the types of thematic maps, use graduated color for rates, sized symbols for counts, and dots for density.
This page sits within the wider field of geospatial data visualization, and it helps you pick a style before you build anything.
| Map style | What the documentation says |
|---|---|
| Graduated color | A light-to-dark ramp suits low-to-high values such as age, income or ratio |
| Rates and percentages | Divide raw data by another field, such as per capita or per square kilometer |
| Proportional symbols | Larger symbols equate to larger numbers |
| Dot density | Each dot represents a constant number of things |
| Dot density projection | Use an equal-area coordinate system |
These points come from Esri’s ArcGIS Online styling guide and its ArcGIS Pro dot density page. Software guidance can change, so check the source before you rely on it.
Start with what your data measures
Every choice below depends on one question: are your values raw counts or already standardized? Esri’s documentation says raw counts are better visualized with colors after they are standardized, as described in the ArcGIS Online guide.
Before you pick a style, answer three quick questions:
- Is each value a count, such as people, or a rate, such as people per square kilometer?
- Do you want readers to read exact amounts, or to see a general pattern?
- Do your places differ a lot in area?
This guide covers three styles that the supporting documentation describes: color, sized symbols and dots. Flow and movement maps are outside that documentation, so they are not covered here.
Graduated color for rates and amounts
A graduated color map shades each place by its value. According to the ArcGIS Online documentation, a simple light-to-dark ramp is good for low-to-high values such as age, income or ratio. Color ramps can be applied to points, lines and polygons.
Normalizing comes first. A Divided by option turns raw data into rates or percentages, and the documented examples are x per capita, y per square kilometer, or a ratio of x to y, per the same guide.
You can also group the values. Turning on classification lets you choose the classification method and the number of classes to generalize the map further, as the Esri styling steps explain.
Check the histogram before you settle. Moving the handles on the ramp and reading the calculated average helps you understand how the data is distributed and fine-tune the message of the map, according to the ArcGIS Online page.
For the build steps behind shaded-area maps, see this guide on how to make a choropleth map.
Proportional symbols for counts
Proportional symbols use an intuitive logic: larger symbols equate to larger numbers. Esri says points, lines and areas can all be drawn this way in its ArcGIS Online guide.
For polygons such as counties, a proportionally sized point symbol draws at the center of each polygon. You can also set a uniform background symbol that draws below the points, according to the ArcGIS Pro documentation.
Pick between relative size and actual size. Relative size fits counts such as population or number of bushels harvested, or values whose unit is unknown, while actual size fits values with a known unit of measure, per the ArcGIS Pro page. Its example is a layer of individual trees with an attribute for tree crown radius, measured in feet.
Readers misjudge circles. The same page notes a tendency to underestimate the size of proportional circles, especially at the larger end of the size range, and offers appearance compensation based on research by James Flannery to scale larger symbols up. It works only with relatively sized symbols and no maximum size, as the Esri documentation states.

Dot density for showing distribution
A dot density map shows quantities inside polygons as a collection of point symbols. Each dot represents a constant number of things, people or other quantifiable phenomena, according to the ArcGIS Pro documentation.
Finer polygons give a more natural look. Esri suggests symbolizing a fine-grained dataset, such as United States counties, with a completely transparent polygon symbol, then laying it over a coarser layer such as states, as the dot density page describes.
Tune the dot value and dot size by trial. The guidance is to avoid dots so close that they form solid areas that obscure patterns, or so far apart that variations in density are hard to see, per the same page.
Most dot maps show one field. When you need to compare distributions of different types, you may map two or three fields, and the documentation gives a home-ownership versus renting comparison as its example, in the Esri dot density guide.
The method relies on the relative visual density of symbols in each polygon, so Esri asks for an equal-area coordinate system on any map that includes dot density symbology. See the caution on the Esri page.
How do you choose between the three styles?
Work through your data in order, and the right style usually becomes clear:
- Decide whether the numbers are counts or rates. Rates and percentages suit graduated color.
- If readers must compare amounts between places, choose sized symbols so that larger symbols stand for larger numbers.
- If the question is where something concentrates inside areas, choose dots.
- Check the projection and the legend before you publish.
A poor match between data and style can send readers the wrong message, which the guide to misleading maps explores in more detail.
Settings that can change the message
Small defaults shape what people see. These are worth checking in Esri’s tools:
- Maximum symbol size: leaving the range open-ended keeps symbols truly relative, but it may result in some excessively large symbols if there is a significant spread in the values, per the ArcGIS Pro documentation.
- Draw order: when symbology is based on a single field, larger features draw first and smaller ones draw above them, according to the same documentation.
- Missing data: a toggle named Show features with no value draws locations with missing data and lets you set a style and label for them, as the ArcGIS Online guide explains.
- Projection: for accurate actual-size symbols, use an equal-area projection, especially over a large geographic extent, per the Pro page.
Frequently asked questions
Can I shade a map with raw counts?
Show answer
It is better to standardize first. Esri’s tools include a Divided by menu for that step, described in the ArcGIS Online guide, so a large place does not look intense only because it is large.
What separates proportional symbols from graduated symbols?
Show answer
Graduated symbols sort features into distinct classes. Proportional symbols instead show quantitative values as unclassed symbols, each sized to its own value, per the ArcGIS Pro documentation.
Why does the projection matter for dots?
Show answer
A projection that preserves area keeps the visual comparison of polygon densities valid, according to the Esri dot density page.
Does this page explain movement or flow maps?
Show answer
No. The documentation behind this page covers color, sized symbols and dots only, so look for a dedicated source if your data describes travel between places.



